Dog Run Panels: A UK Buyer Guide

Most buyers order run panels the same way they order garden furniture: pick a size, find the cheapest option, and hope for the best. That approach works fine until the panels rust through in three winters, a large dog bends the bars, or a licensing inspection flags the height as non-compliant. I’ve been sourcing panels for a commercial kennel build in Ayrshire over the past several months, and the research involved has been more involved than I expected. This guide covers what I’ve learned about the decisions that actually matter.

Dog run panels are a distinct product from the kennel wall or sleeping pod panels used in the structure itself. If you are looking at panels for the kennel building rather than the outdoor run, the kennel panels guide covers that separately. What this guide addresses is the modular fencing system that creates the enclosed run space: the panels, gate, and any dividers.

The Two Panel Families

Every dog run panel in the UK market falls into one of two structural categories: bar panels or welded mesh panels. They look superficially similar but behave differently in practice.

Bar panels use horizontal and vertical steel bars welded at intervals. The gap between bars is either 5cm or 8cm depending on the product. Bar panels are heavier, more rigid, and generally more resistant to a dog throwing its full weight against them. The 5cm bar spacing is better suited to most medium and large breeds. The 8cm spacing works for giant breeds where the wider gap does not present an entrapment risk, and gives better airflow and visibility. Bar panels with 5cm spacing are the standard choice for commercial kennel runs.

Welded mesh panels use a grid of thinner steel wire, typically in a 5cm x 5cm or 7.5cm x 5cm aperture. They weigh less, cost less per panel, and work well for smaller breeds or puppies where the tighter mesh prevents paw entrapment. The trade-off is that mesh panels are less resistant to repeated lateral pressure from large or strong dogs. A Border Collie leaning against a mesh panel is fine. A Rottweiler throwing itself at one repeatedly is a different calculation.

For a licensed commercial kennel, bar panels are the practical choice. For domestic use with a medium breed that does not challenge fencing, mesh is serviceable.

Material and Coating: Galvanised vs. Powder-Coated

This is where most buyers make their first mistake. Powder-coated panels look good in product photos. They ship with an even colour finish and photograph well for a kennel marketing brochure. The problems start at the anchor points.

When you bolt a panel to a concrete base or to a corner post, the powder coat at that contact point chips. Once the coating breaks, bare steel is exposed to moisture, urine, and cleaning chemicals. That is where rust begins. In Scotland’s climate, you will see it within two to three years. In a commercial kennel that is cleaned down daily, you will see it faster.

Hot-dip galvanised panels work differently. The steel is immersed in molten zinc after fabrication, which bonds metallurgically with the steel surface rather than sitting on top of it. The zinc coating is typically 85 microns thick or more, compared to 60-80 microns for a standard powder coat applied over bare steel. Critically, the zinc coating is sacrificial: it corrodes preferentially to the underlying steel and continues protecting the panel even where the surface is scratched or worn. British Standard BS EN ISO 1461 governs the minimum zinc thickness for hot-dip galvanised structural steel; panels certified to this standard are the ones worth buying.

One thing worth checking before you order: does the manufacturer hot-dip galvanise the assembled panel, or do they use pre-galvanised steel before welding? The distinction matters at the weld points. Welding destroys the zinc coating in the immediate area around the weld. If the panel is galvanised after welding, the entire structure including every weld junction receives continuous zinc coverage. If pre-galvanised steel is welded cold, the weld points are exposed and will rust first. I missed this question on my first round of supplier calls. That’s on me. When I went back and asked specifically, the answers varied considerably across UK suppliers.

A Note on Cleaning Chemicals

Galvanised steel performs well across a pH range of 5.5 to 12, according to the American Galvanizers Association. Most kennel disinfectants, including quaternary ammonium compounds and phenolic products, fall well within that range. Strongly acidic cleaners (below pH 5.5) will attack the zinc coating over time. If you are using a disinfectant with a pH below 6, check the data sheet and switch to a neutral or mildly alkaline product. Most professional kennel disinfectants are formulated to be surface-safe and will not cause problems with hot-dip galvanised panels used at correct dilution.

Gauge and Bar Thickness: What to Look For

Gauge is the wire or bar diameter, and it matters more for welded mesh than for bar panels. For bar panels, the physical bar diameter (usually expressed in millimetres, not gauge) is the relevant figure. A 12mm diameter bar is standard for commercial-grade kennel panels. Some budget panels use 10mm bar; the difference is noticeable when a large dog pushes against the panel.

For welded mesh panels, wire gauge runs from 4mm (heavy duty, 8 gauge equivalent) down to 2.5mm (lighter residential use). Anything over 20kg warrants a minimum of 3.5mm wire. Strong breeds, powerful terriers, or any dog known to challenge fencing should have 4mm wire; the additional cost is marginal against the replacement cost if the panel fails. The weld quality at the wire intersections is equally important: pull two adjacent wires apart at a joint on a sample panel before ordering a full run. A good weld holds; a poor one separates with light pressure, leaving a gap and a potential injury point.

Run Height: What a Licensed Kennel Requires

In England, the Animal Welfare (Licensing of Activities Involving Animals) (England) Regulations 2018 require a minimum internal headroom of 1.8m for kennel units. The exercise run must have a secure, waterproof roof over at least half its total area. Run panels that bring the internal height below 1.8m will not pass inspection.

In Scotland, the Animal Welfare (Licensing of Activities Involving Animals) (Scotland) Regulations 2021 set a 2m minimum total enclosure height for kennel units. Run panels sold at the standard 1.84m height (which satisfies England) may not satisfy Scottish licensing conditions without supplementary roof-height framing. If you are building a licensed kennel in Scotland, verify with your local authority before specifying panel height.

Most reputable UK suppliers sell standard run panels at 1.84m high, which accounts for the English minimum with a small clearance. Confirm the internal measurement against the supplier’s specification sheet, not the nominal product description.

Gate Panels: Options and Mistakes

Every run needs at least one gate panel, and this is where the purchase goes wrong more often than you would expect. Gate panels are the same height and material as the run panels but hinged on one side and latched on the other. The common mistakes are ordering the wrong hand (hinge left vs. hinge right), ordering a gate that swings into the run rather than out (fine until a large dog leans against it and traps it closed from the inside), and buying a gate with a latch that a clever dog can manipulate.

For a commercial kennel, double-action hinges that allow the gate to swing both ways are worth the additional cost. They make cleaning rounds faster when your hands are full. Padlock hasps on commercial kennel gates are not optional: they prevent guests from accidentally releasing dogs and satisfy the security requirements under licensing conditions.

Some suppliers offer a half-gate (a solid panel from floor to approximately 90cm, with bars above) which prevents a dog from jumping at the lower section. These are useful for breeds that bounce off doors repeatedly; they take more punishment on the lower section and the solid fill absorbs impact better than bars alone.

How to Calculate How Many Panels You Need

Quick formula: calculate the perimeter of your run (2 x length + 2 x width), subtract one panel width for the gate, then divide by the standard panel width (most UK bar panels are sold at 1m, 1.5m, or 2m widths). Round up. Order one gate panel separately.

As a worked example: a single-bay run of 3m x 2m has a perimeter of 10m. With 1m-wide panels and one 1m gate, you need 9 full panels plus the gate. Add a roof panel if your licensing condition requires one (it does, for commercial kennels). If the run shares a wall with the kennel building, subtract that wall length from the perimeter calculation.

Panel width standardisation varies by supplier. Some sell primarily in 2m widths; some in 1m; some offer custom widths. If your run dimensions don’t divide evenly into standard panel widths, you either accept a partial gap at one end (covered with a cut section and a post) or order a bespoke-width panel. Most UK suppliers offer bespoke widths at an additional lead time. Get this sorted before you pour your concrete base posts, not after.

Modularity and Layout Changes

One of the practical advantages of modular panel systems is the ability to reconfigure the run layout later. In a permanent-construction run (block or brick walls with a mesh top), any layout change requires demolition. A panel system bolts together with standard fixings; you can add a bay, extend a run length, or divide a run into two smaller ones by adding panels and adjusting the frame.

This flexibility matters more than most first-time buyers realise when they are commissioning a kennel. The run configuration you design at planning stage is rarely the one you want after a year of operating, once you understand your actual guest mix, your cleaning workflow, and which dogs do better with more lateral space versus more length. A panel system accommodates that learning. A block-built run does not.

Check that the panels you order use a standard post and connector system compatible with other suppliers’ panels. Some systems use proprietary connectors that lock you into one supplier for all future additions. That is not necessarily a problem if the supplier is established, but it is worth knowing before you commit.

Supplier Questions Worth Asking

Before placing an order with any UK supplier, get answers to these five questions in writing:

  1. Are the panels hot-dip galvanised after welding, or are they made from pre-galvanised steel and then welded? (You want: galvanised after welding.)
  2. What is the zinc coating thickness, and does the product comply with BS EN ISO 1461? (You want: compliance confirmed.)
  3. What is the bar diameter or wire gauge? (You want: 12mm bar for bar panels, 3.5-4mm wire for mesh.)
  4. What is the lead time for bespoke widths, and is there a minimum order for bespoke sizes?
  5. What fixings are used, and are they compatible with concrete base anchoring?

Any supplier who cannot answer the first two questions in writing is not a supplier I would use for a commercial build. The galvanising specification is the most important quality indicator and any reputable manufacturer knows it.

For context on planning the full run, including ground preparation, drainage, and surface choices, the outdoor kennel run guide covers the broader project. The run panels are one component of that. And if you are working through the wider kennel build, the kennel overview sets out what a compliant commercial facility involves from the ground up.

Frequently Asked Questions

What Are the Best Dog Run Panels for Large Dogs?

For large breeds, hot-dip galvanised bar panels with 5cm bar spacing and a 12mm bar diameter are the appropriate specification. The 5cm spacing prevents a large dog’s head from passing through. Welded mesh is less suitable for large, strong, or persistent dogs as repeated lateral pressure can deform the wire joints over time.

How Tall Do Dog Run Panels Need to Be for a Licensed Kennel?

In England, the minimum internal height under the 2018 Animal Welfare licensing regulations is 1.8m. In Scotland, the 2021 Regulations set a 2m minimum for the total enclosure height. Standard UK run panels are sold at 1.84m; verify with your local authority in Scotland whether additional framing is required to meet the 2m threshold.

How Many Panels Do I Need for a Dog Run?

Calculate the run perimeter (2 x length + 2 x width), subtract the gate panel width, and divide by your panel width. For a 3m x 2m run with 1m panels and a 1m gate, that is 9 full panels plus one gate panel. Always order one spare panel if your budget allows; delivery minimums and lead times make late additions costly.

Are Galvanised Dog Run Panels Safe to Use with Kennel Disinfectants?

Yes, provided the disinfectant pH falls between 5.5 and 12. Most professional kennel disinfectants are formulated within this range. Avoid strongly acidic cleaners used at full concentration on galvanised surfaces, as they will degrade the zinc coating over time. Rinse panels after disinfection if the product label recommends it.

Leave a Comment